Nodal Australia Distribution and WholesaleINSTEON DIN-Rail Dimmer
| Product code: IN2452-522 | |||
Quick-start guide
Image packThe INSTEON DIN-Rail Dimmer clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON keypad or other INSTEON Controller for full remote control over the module and it's connected load.
- Simply clip onto 35mm DIN rail and wire like any other INSTEON Controller
- Optional sense wires allow for control via a connected, hard-wired switch
- Compatible with latching, single-momentary and dual-momentary switches
- Award-winning INSTEON technology provides superior reliability
- This product should be installed by a licensed electrician
General |
� |
| Product Name: | INSTEON DIN-Rail Dimmer |
| Product Code: | 2452-522 |
| Regions: | Australia and New Zealand |
| In the box: | INSTEON DIN-Rail Dimmer |
INSTEON |
� |
| INSTEON: | Controller and responder |
| Maximum links/scenes: | 400 |
| Load brightness levels: | 32 locally (256 with software) |
| Status LED: | Green when load is on, red when load is off, Blinks green or red during setup, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software) |
| LED brightness: | Adjustable from off to 100% bright |
| Local ramp rate: | Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 8 minutes with software) |
| Local control: | Yes |
| Commands supported as controller: | On /�Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim |
| Commands supported as responder: | On / Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim, Incremental brighten / Incremental dim, Beep |
| Software configurable: | Yes |
| RF range: | 45m |
| Phase detect beacon: | Yes |
| X10 support: | Yes |
| X10 addresses: | Any 1 of 256 (unassigned by default) |
| INSTEON device category: | 0x01 dimmable lighting control |
| INSTEON device subcategory: | 2453-222 (921MHz), 0x34 |
Operation |
� |
| Status LED: | Green. Blinks on activation |
| Sense Modes: | Jumper Installed: Open = Group 1 On, Closed = Group 1 Off; Jumper Uninstalled: Open = Group 1 On (or off), Closed = Group 2 On (or Off) |
| Aux. Sensor Input: | Senses contact closure |
| Aux. Sensor Input Wire: | >= 20 gauge wire |
| Setup Memory: | Non-volatile EEPROM |
Mechanical |
� |
| Mounting: | 35mm (top hat) DIN rail | Max. cable size: | 4mm�, 12 AWG (2.72mm diameter) |
| Min. cable size: | 1.5mm�, 15 AWG |
| Screw DIN rail connections: | Line, Neutral, Load, Sense 1, Sense 2 | Casing: | UV stabalized plastic (INSTEON White) | Set button: | Yes | Beeper: | Yes | Beep on button press: | Optional (off by default) | LED: | 1 RGB |
| Dimensions: | 80mm W x 53mm H x 63mm D |
| Weight: | 175g |
| Operating Conditions: | Indoors, 0� C to 40� F, up to 85% relative humidity |
Electrical |
� |
| Voltage: | 100VAC to 240VAC |
| Frequency: | 50/60Hz auto-detected at power-up |
| Max. load: | 300W at 100-240VAC |
| Load types: | Incandescent |
| User replaceable fuse: | Yes (16 A (T)) 5x20mm fuse |
| Retain all settings without power: | Yes, saved in non-volatile EEPROM |
| Standby power consumption: | <1W |
| Certification: | Approved for use in Australia and New Zealand |
Nodal Australia do not supply directly to retail customers. To purchase this product please contact www.envioustechnology.com.au.
To locate other resellers please contact us.
If your business is in a compatible industry then you may be interested in becoming a reseller for Nodal Australia.